Permagen’s 0.2 mL PCR / 1.5 mL Microcentrifuge tube separation rack is designed for labs with both PCR strip and 1.5 mL separation protocols. On the top, hold up to two of either 8 or 12 strips, or up to 24 individual tubes. Flip over and hold up to twelve 1.5 mL Microcentrifuge Tubes

Features include solid aluminum alloy design with hard coat finish for years of trouble-free use, rubber feet on both sides to help prevent slipping on work bench, less tippy than common plastic products, and fast separations using any magnetic beads

SKU #

MSR1224B

Features

• Aluminum alloy design for years of trouble-free use
• Fast magnetic bead separations
• Held to tighter tolerances for more consistent results
• Pulls beads to side of wells for easy tip tracking down opposite side
• Rubber feet to help prevent slippage
• Stable design
• Angled tube holes which allow the tubes to come close to magnets

Compatibility

• Most 1.5 mL Microcentrifuge tubes
• Some 2.0 mL Microcentrifuge tubes
• 8-strip PCR tubes
• 12-strip PCR tubes
• Individual PCR tubes 
• Any Magnetic Beads

Volumes

Minimum Volume 0.2 mL PCR Tube – 10 µL

Maximum Volume 0.2 mL PCR Tube – 0.2 mL

____________________________________________

Minimum Volume 1.5 mL Microcentrifuge Tube – .5 mL

Maximum Volume 1.5 mL Microcentrifuge Tube – 1.5 mL

Permagen’s 0.2 mL PCR / 1.5 mL Microcentrifuge tube separation rack is designed for labs with both PCR strip and 1.5 mL separation protocols. On the top, hold up to two of either 8 or 12 strips, or up to 24 individual tubes. Flip over and hold up to twelve 1.5 mL Microcentrifuge Tubes

Introduction

This product provides a reliable solution for DNA isolation from yeast samples. Total DNA can be purified from yeast (<5x 10⁷) without phenol or chloroform. The whole extraction can be finished within 60 minutes. Purified DNA can be directly used for PCR, Southern blot, ect.

Details

Specifications

Features	Specifications
Main Functions	Isolation total DNA from yeast cultures
Applications	PCR, southern blot and enzyme digestion, etc.
Purification method	Mini spin column
Purification technology	Silica technology
Process method	Manual (centrifugation or vacuum)
Sample type	Yeast culture
Sample amount	Bacterial culture: 1-1.5 ml
Elution volume	≥30μl
Time per run	≤60 minutes
Liquid carrying volume per column	800μl
Binding yield of column	100μg

Principle

This product is based on silica Column purification. The sample is lysed and digested with lysate and protease, DNA is released into the lysate. Transfer to an adsorption column. Nucleic acid is adsorbed on the membrane, while protein is not adsorbed and is removed with filtration. After washing proteins and other impurities, Nucleic acid was finally eluted with low-salt buffer (10mm Tris,pH9.0, 0.5mm EDTA).

Advantages

• Fast – several samples can be extracted in 40 minutes (after digestion)
• High purity – purified DNA can be directly used in various downstream applications
• Good repeatability – silica technology can obtain ideal results every time
• High recovery – DNA can be recovered at the level of PG
• Sufficient components – lysozyme, protease K, RNase A and glass beads

Kit Contents

Contents	D314702	D314703
Purification Times	50 Preps	250 Preps
Hipure DNA Mini Columns I	50	250
2ml Collection Tubes	50	250
Glass Beads (0.4~0.6mm)	20 g	90 g
Buffer SE	30 ml	150 ml
Lyticase	1.8 ml	5 x 1.8 ml
Buffer ATL	30 ml	150 ml
ReagentDX	500 μl	1500 μl
Buffer DL	30 ml	150 ml
Buffer GW1*	13 ml	66 ml
Buffer GW2*	20 ml	2 x 50 ml
Proteinase K	12 mg	60 mg
Protease Dissolve Buffer	1.8 ml	5 ml
Buffer AE	15 ml	30 ml

Storage and Stability

Proteinase K should be stored at 2–8°C upon arrival. However, short-term storage (up to 12 weeks) at room temperature (15–25°C) does not affect their performance. The remaining kit components can be stored dry at room temperature (15–25°C) and are stable for at least 18 months under these conditions. Buffer ATL may precipitate at low temperature. Dissolve it by 37℃ water bath.

This product provides a reliable solution for DNA isolation from yeast samples. Total DNA can be purified from yeast (

The Permagen ring magnet low elution plate with integrated cushion base plate was designed for use in automation applications where volumes as low as 5 µL are required. Most PCR plates are bent, leading to inconsistent lab results. Unlike most products, we have added an angled frame around the top of our plate, this helps with two things, straightening out the PCR plate, and leading it to the proper location on the magnets during automation while the cushion assist compensates for labware inconsistencies. 

SBS SLAS Footprint (127.75mm x 85.50mm) to fit into any automated liquid handling robot 

Features include solid aluminum alloy construction and hard coat anodized finish for years of trouble-free use, and compatible with any magnetic beads

SKU #

RLE500R

Features

• SBS/ SLAS footprint
• Integrated cushion base for precise pipetting
• Solid Aluminum alloy design
• Precision manufactured for more consistent results
• Fast magnetic bead separations
• Integrated bracket to help keep microplate in place and flat
• Made in USA 
• For Research use only

Compatibility

• Full- skirt PCR plates
• 1/2- skirt PCR plates 
• Un-skirted PCR plates
• Any magnetic beads
• Any common liquid handlers i.e. SPTLabtech Firefly®, Tecan®, Opentrons®, Hamilton®, Agilent®, Beckman®, etc.

Volumes

Maximum  – 150 µL 

Minimum  – 5 µL 

The Permagen ring magnet low elution plate with integrated cushion base plate was designed for use in automation applications where volumes as low as 5 µL are required. Most PCR plates are bent, leading to inconsistent lab results. Unlike most products, we have added an angled frame around the top of our plate, this helps with two things, straightening out the PCR plate, and leading it to the proper location on the magnets during automation while the cushion assist compensates for labware inconsistencies.