GeneAb™ TFE3

Description 

The DM2360 FluoroBand™ 100 bp+3K Fluorescent DNA Ladder is a ready-to-use DNA ladder, which is pre-mixed with high sensitivity DNA binding fluorescent dye and loading dye for direct gel loading. The DNA Ladder DM2360 is composed of 12 individual DNA fragments: 3k, 1.5k, 1k, 900, 800, 700, 600, 500, 400, 300, 200 and 100 bp derived from a mixture of PCR products and specifically digested plasmid DNA; these bands can be visualized when illuminated with 470 nm blue light or UV light. This product contains two enhanced bands (1.5 kb and 500 bp) for easier reference. In addition, two tracking dyes, Xylene cyanol FF and Orange G which mimic the migration of 4,000 bp and 50 bp dsDNA during electrophoresis are also added for real time monitoring. Real time observation of the electrophoresis is also possible if compatible light source is fitted to the electrophoresis tank. 

Features

• Sharp bands
• Quick reference— enhanced bands 
• Ready-to-use— premixed with loading dye for direct loading
• Stable— room temperature storage over 6 months
• Directly observed by UV or blue light— premixed with high sensitive DNA fluorescent dye

Source 

Phenol extracted PCR products and dsDNA digested with specific restriction enzymes, equilibrated in 10 mM Tris-HCl (pH 8.0) and 10 mM EDTA.

Range 

100 ~ 3,000 bp 

Concentration 

56 µg/ 500 µl

Recommended loading volume 

5 µl/ well

Storage

Protected from light 
Room temperature for 6 months
4°C for 12 months 
-20°C for 24 months 

The DM2360 FluoroBand™ 100 bp+3K Fluorescent DNA Ladder is a ready-to-use DNA ladder, which is pre-mixed with high sensitivity DNA binding fluorescent dye and loading dye for direct gel loading. The DNA Ladder DM2360 is composed of 12 individual DNA fragments: 3k, 1.5k, 1k, 900, 800, 700, 600, 500, 400, 300, 200 and 100 bp derived from a mixture of PCR products and specifically digested plasmid DNA; these bands can be visualized when illuminated with 470 nm blue light or UV light. This product contains two enhanced bands (1.5 kb and 500 bp) for easier reference. In addition, two tracking dyes, Xylene cyanol FF and Orange G which mimic the migration of 4,000 bp and 50 bp dsDNA during electrophoresis are also added for real time monitoring. Real time observation of the electrophoresis is also possible if compatible light source is fitted to the electrophoresis tank.

Techinical parameter

Model:
SH7006,SH9006,SH9009

Brand:
Yingtai

Permagen’s Dual Volume 0.2 mL PCR Strip separator uses the same magnet configuration as our MSR812 rack above, however, when using the opposite side, the magnets are positioned towards the bottom of the tubes allowing low elution’s to be achieved.  Angled tube holes allow clean area at the front of the well for clean, fast aspiration without the concern of disturbing bead pellets Features include solid aluminum alloy design with hard coat finish for years of trouble-free use, rubber feet to help prevent slipping on work bench, less tippy than common plastic products, and fast separations using any magnetic beads

SKU #

MSRLV08

Features

• Two racks built into one
• 50 µL – 0.2 mL volumes on one side
• 5 µL – 50 µL volumes on opposite side
• Sides are conveniently marked with volume recommendations
• Fast magnetic bead separations
• Held to tighter tolerances for more consistent results
• Pulls beads to side of wells for easy tip tracking down front side
• Rubber feet to help prevent slippage on both sides
• Stable, solid aluminum design
• Angled tube holes which allow the tubes to come close to magnets

Compatibility

• Up to 16 Individual PCR tubes per side
• Up to two, 8-strip PCR tube strips per side
• Any Magnetic Beads

Volumes

Maximum  – .2 mL 

Minimum  – 5 µL 

Permagen’s Dual Volume 0.2 mL PCR Strip separator uses the same magnet configuration as our MSR812 rack above, however, when using the opposite side, the magnets are positioned towards the bottom of the tubes allowing low elution’s to be achieved. Angled tube holes allow clean area at the front of the well for clean, fast aspiration without the concern of disturbing bead pellets Features include solid aluminum alloy design with hard coat finish for years of trouble-free use, rubber feet to help prevent slipping on work bench, less tippy than common plastic products, and fast separations using any magnetic beads